Model Series | JMTX-ADN1 |
Part Number | JMTX-ADN1-N97000 | JMTX-ADN1-N97008 (64GB eMMC and TPM 2.0) |
Form Factor | Mini-ITX (170 x 170mm) |
Processor | Intel® Processor N97, up to 3.60 GHz, 4-Core 4-Thread, 12W TDP (Products formerly Alder Lake-N) |
Memory | 1 x 262-pin Single Channel DDR5-4800 SO-DIMM up to 16GB Total |
Graphics | Intel® UHD Graphics Up to 3 Displays |
Audio | Realtek ALC897 HD Audio, 3W Amplifier |
LAN | 2 x Intel I226-V PCIe 2.5GbE |
Storage | 1 x SATA3 6Gb/s 1 x M.2 (SATA/PCIe 3.0 x2, M-key, 2242 2280 NVMe) | 1 x SATA3 6Gb/s 1 x M.2 (SATA/PCIe 3.0 x2, M-key, 2242 2280 NVMe) Onboard 64GB eMMC |
Super IO | FINTEK F81966D |
TPM | Intel fTPM 2.0 (PTT) | Intel fTPM 2.0 (PTT) Onboard NUVOTON TPM v2.0 |
Back Panel Connectors |
2 RJ45 LAN (10/100/1000/2500)
2 USB 2.0 Port
1 USB 3.2 Gen 2 (10 Gb/s)
1 USB 3.2 Gen 2 (10 Gb/s) Type-C with DP 1.4 (4096 x 2304 @ 60Hz)
2 HDMI 2.0b (4096 * 2160 @ 60Hz)
1 3.5mm Combo Line-out/MIC Jack
1 Serial Port (1 * RS232/422/485)
1 +12V - 28V 2.5mm Diameter DC Power Jack
|
Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242/2280 (SATA/PCIe 3.0 x2 NVMe)
1 M.2 B-key, 3042/3052 (USB3.2/USB2.0 for 3G/LTE Modem)
1 M.2 E-key, 2230 (PCIe 3.0 x1/USB 2.0/CNVi for WiFi)
5 Serial Headers (5 * RS232)
2 USB Pin Headers for 4 additional USB 2.0 Ports
1 LVDS/eDP (1920 * 1200 @ 60Hz)
1 Inverter
1 Nano SIM Socket
1 8 bit GPIO Header
1 5-pin SMBUS Header
2 4-pin Fan Header
1 9-pin Front Audio Header
1 Speaker Header
1 PS2 Keyboard/Mouse Header
1 Chassis Intrusion Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 4-pin Alternate Power-in Connector
|
Power Supply for JMTX-ADN1 |
External Power Supply – the board can be powered with a +12V – 28V external power supply though a DC connector on the back panel. The rear +12V – 28V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V – 28V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V – 28V 2x2 power connector, where pins 3 and 4 are +12V – 28V and pins 1 and 2 are GND. The connector used is Molex Micro-Fit (3mm pitch), right-angled, 4-pos/dual row (2x2).
Caution: There is no isolation circuitry between the external +12V – 28V DC jack and the internal 2x2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V – 28V DC jack is covered if the internal 2x2 power connector is to be used.
|
Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM/Digital Signage)
√ Digital Security / Surveillance
√ Panel PC
|
Environment |
Operating Temperature : -20 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|