| Model Series | MF13 |
| Part Number | MF13-03 (32GB eMMC)
MF13-04 (64GB eMMC) | MF13-07 (32GB eMMC, TPM 2.0)
MF13-08 (64GB eMMC, TPM 2.0) |
| Form Factor | 3.5" SBC (148 x 102mm) |
| Processor | Intel® Celeron J6412, 2.00GHz – 2.60GHz Burst, 4-Core 4-Thread, 10W TDP
* Ships with flat silver aluminum heatsink for direct attach |
| Memory | 1 x 260-pin Single Channel DDR4-3200 SO-DIMM up to 32GB Total |
| Graphics | Intel® UHD Graphics for 10th Gen Intel® Processors |
| Audio | Intel® Display Audio (via HDMI) |
| LAN | 4 x Intel I225-V PCIe 2.5GbE |
| Storage | 1 x SATA3 6Gb/s
1 x M.2 (SATA & PCIe 3.0 x2, M-key, 2242/2280 NVMe)
Onboard 32/64GB eMMC |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) | Intel fTPM 2.0 (PTT)
Onboard Nuvoton TPM 2.0 |
| Back Panel Connectors |
1 Serial port (RS232/422/485)
4 RJ45 LAN (10/100/1000/2500)
1 USB 3.2 Gen 2 (10 Gb/s)
1 USB 2.0 Port
1 +12V 2.5mm Diameter Locking DC Power Jack
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242/2280 (SATA & PCIe 3.0 x2 NVMe)
1 M.2 B-key, 3042/3052 (USB 3.2 for 3G/LTE Modem)
1 M.2 E-key, 2230 (PCIe 3.0 x1/USB 2.0 for WiFi)
1 Serial Headers (RS232/422/485)
1 USB Pin Headers for 2 additional USB 2.0 Ports
1 HDMI Header (1920 × 1080 @60Hz)
1 8 bit GPIO Header
1 4-pin SMBUS Header
1 4-pin Fan Header
1 6-pin PS2 Keyboard/Mouse Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 2-pin +12V Alternate DC-in (Mating plug: Molex 5557-02R)
|
| Power Supply for MF13 |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V 2-pin power connector, where pin 1 is +12V and pin 2 is GND. The internal 2-pin power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Networking/Storage Server/Mail Server/Print Server
√ Industrial Automation/Control
√ Medical
√ IoT
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
