| Model Name | NC8J |
| Part Number | JNC8J-3455 |
| Form Factor | Thin Mini-ITX (170 x 170mm) |
| Processor | Intel® Celeron J3455 Processor Quad Core 1.50 GHz - 2.30 GHz, 10W TDP |
| Memory | 1 x 204-pin DDR3L-1866 SO-DIMM up to 8GB (1.35V required) |
| Graphics | Intel HD Graphics 500, 250MHz - 750MHz (J3455) |
| Audio | Realtek ALC662VD HD Audio Codec with 3W Amplifier |
| LAN | 1 x Realtek® RTL8111G PCI-E Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s Connector
1 x M.2 SATA M-key 2242 length
Optional: 32GB eMMC |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware |
| Back Panel Connectors |
1 +12V 2.5mm Diameter DC Power Jack
2 Serial (RS232)
1 USB 2.0
2 USB 3.0
1 RJ45 LAN (10/100/1000)
1 3.5mm Audio Jack (Line-out)
|
| Onboard I/O Connectors |
1 PCI-E x 1
1 SATA3 6Gb/s Connector
1 M.2 SATA 2242 M Key for SSD
1 M.2 2230 E Key for WiFi
2 Serial Headers (1 * RS232, 1 * RS232/422/485) 2.00mm pitch
2 USB Pin Headers for 4 additional USB 2.0 Ports 2.00mm pitch
1 HDMI (3840 * 2160 @ 30Hz)
1 29-pin eDP (4096 * 2160 @ 60Hz)
1 30-pin LVDS (2560 * 1600 @ 60Hz)
1 6-pin Inverter 5V/12V
1 25-pin Parallel Header
1 8 bit GPIO Header
1 6-pin PS/2 Header
1 9-pin Front Audio Header
1 4-pin Speak-out 3W Amplifier Header
1 5-pin SMBUS Header
2 3-pin Fan Header
1 AT/ATX Mode Jumper
1 Chassis Intrusion Jumper
1 4-pin SATA Power Output (Male)
1 4-pin +12V Alternate ATX Power-out
|
| Power Supply for NC8J |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V 4-pin power connector, where pins 3 and 4 are +12V DC and pins 1 and 2 are GND. The connector used is Molex Micro-Fit (3mm pitch), right-angled, 4-pos/dual row (2x2).
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 4-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 4-pin power connector is to be used.
|
| Market Segments Supported |
√ Digital Signage
√ Industrial Panel PC
√ Retail (POS/Kiosk/ATM)
|
| Environment |
Operating Temperature : -10 ~ 60°C
Storage Temperature : -20 ~ 70°C
|
