| Model Series | MF10 |
| Part Number | MF10-20 | MF10-22 |
| Form Factor | 3.5" SBC (148 x 102mm) |
| Processor | 11th Gen Intel® Core i5-1145G7E, 1.50GHz – 4.10GHz Burst, 4-Core 8-Thread, 15W TDP, vPro (Formerly Tiger Lake)
* Ships with flat silver aluminum heatsink for direct attaching to a surface |
| Memory | 2 x 260-pin Dual Channel DDR4-3200 SO-DIMM up to 64GB Total |
| Graphics | Intel® Iris® Xe Graphics |
| Audio | Realtek ALC888S/ALC662 HD Audio with 3W Amplifier |
| LAN | 1 x Intel I225-V PCIe 2.5GbE
1 x Intel I219-LM PHY Gigabit LAN (iAMT 12.0) |
| Storage | 1 x SATA3 6Gb/s
1 x M.2 (PCIe 4.0 x4 & SATA, M-key, 2242/2280 NVMe) |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 3.5mm Line-out & MIC-in Audio Combo Jack
1 RJ45 LAN (10/100/1000/2500)
1 RJ45 LAN (10/100/1000)
3 USB 3.2 Gen 2 (10 Gb/s)
1 USB 2.0
2 HDMI 2.0b (4096 * 2160 @ 60Hz, 4K HDR)
2 USB 3.2 Gen 2 Type-C for DP 1.4 (4096 * 2304 @ 60Hz)
Up to 4 * 4K Displays or 1 * 8K Displays (Type-C/DP)
1 +12V – 24V 2.5mm Diameter DC Power Jack
1 Nano SIM Socket
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242/2280 (PCIe 4.0 x4 NVMe & SATA)
1 M.2 E-key, 2230 (USB and PCIe CNVi WiFi)
1 M.2 B-key, 3042/3052 (USB and PCIe for SIM)
1 Serial Headers (RS232)
1 USB Pin Headers for 2 additional USB 2.0 Ports
1 40-pin eDP (4096 * 2304 @ 60Hz)
1 Nano SIM Socket (Bottom)
1 8 bit GPIO Header
1 4-pin 3W Amplifier Header
1 6-pin PS2 Keyboard Mouse Header
1 4-pin SMBUS Header
1 4-pin Fan Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 2-pin +12V – 24V Alternate Power-In (Mating plug: JST VHR-2N or TE 1-1123722-2)
|
| Power Supply for MF10 |
External Power Supply – the board can be powered with a +12 - 24V external power supply though a DC connector on the back panel. The rear +12 - 24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12 - 24V and the shell is GND. A minimum of 90 Watts power adapter is recommended.
Internal Power Supply – the board can alternatively be powered via the internal +12 - 24V 2-pin power connector, where pin 1 is +12 - 24V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +12 - 24V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12 - 24V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM/Digital Signage)
√ Digital Security / Surveillance
√ Panel PC
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
