| Model Series | NF631R |
| Part Number | JNF631R-3455
JNF631R-3350 |
| Processor | Intel® Celeron J3455 Processor Quad Core 1.50 GHz - 2.30 GHz, 10W TDP
Intel® Celeron N3350 Processor Dual Core 1.10 GHz - 2.40 GHz, 6W TDP
* Ships with black finned heatsink for bench testing |
| Memory | 1 x 204-pin DDR3L-1866 SO-DIMM up to 8GB (1.35V required) |
| Graphics | Intel HD Graphics 500, 250MHz - 750MHz (J3455)
Intel HD Graphics 500, 200MHz - 650MHz (N3350) |
| Audio | Realtek ALC888 HD Audio |
| LAN | 2 x Realtek RTL8119I PCI-E Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s Connector
1 x M.2 SATA M-key 2242 length only |
| Super IO | FINTEK F81866 |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware |
| Back Panel Connectors |
2 RJ45 LAN (10/100/1000)
4 USB 3.0
1 3.5mm Combo Line-out/MIC Jack
1 RJ45 Type Serial Port (RS232)
2 Display Port (4096 x 2160 @ 60Hz)
1 +12V 2.5mm Diameter DC Power Jack
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 SATA 2242 only
1 Mini PCI Express Slot (Full-size)
5 Serial Headers (4 * RS232, 1 * RS232/422/485)
1 USB Pin Headers for up to 2 additional USB 2.0 Ports
1 40-pin eDP (3840 * 2160 @ 60Hz)
1 SIM Card Socket
1 Micro SD Card Slot
1 8 bit GPIO Header
1 AT/ATX Mode Jumper
1 6-pin PS/2 Mouse/Keyboard Header
1 9-pin Front Audio Header
1 5-pin SMBUS Header
2 4-pin CAN bus
1 4-pin Fan Header
1 4-pin Floppy Power Output (Male)
1 2-pin +12V Alternate Power Connector
|
| Power Supply for NF631R |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V 2-pin power connector, where pin 1 is +12V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Digital Signage
√ Retail (POS/Kiosk/ATM)
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
