| Model Name | NF797 |
| Part Number | JNF797-Q370 |
| Form Factor | Mini-ITX (170 x 170mm) |
| Processor | 8th & 9th Gen Intel® Core i7 / i5 / i3 / Pentium Processor up to 65W
Socket LGA 1151 (Formerly Coffee Lake) |
| Chipset | Intel Q370 |
| Memory | 2 x 260-pin SODIMM un-buffered Dual Channel DDR4-2666 up to 64GB Total
* Core i3, Pentium, and Celeron can only support DDR4-2400 up to 32GB Total |
| Graphics | Requires Intel Core processor with Intel HD Graphics |
| Audio | Realtek ALC662VD HD Audio |
| LAN | 1 x Intel I219-LM PHY Gigabit LAN (iAMT 12.0)
1 x Intel I211-AT PCI-E Gigabit LAN |
| Storage | 2 x SATA3 6Gb/s with RAID 0, 1
1 x M.2 Slot (M-key, SATA & PCIE 3.0 x4, 2242/2260/2280) |
| Super IO | NUVOTON NCT6116D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
* As of 5/11/2020, onboard TPM is now optional |
| Back Panel Connectors |
1 9 ~ 36V DC-in Jack (1-pin 2.5mm ID, 5.5mm OD)
1 HDMI 1.4 (4096 * 2160 @ 30Hz)
2 DP 1.2 (4096 * 2304 @ 60Hz )
2 Serial Port (2 * RS232/422/485)
4 USB 3.1 Gen 2 (10 Gb/s)
2 RJ45 LAN (10/100/1000)
3 3.5mm Audio Jack
|
| Onboard I/O Connectors |
1 PCI-E x4 Side-Slot, Supports Jetway ETC4G & ETC4B Expansion Modules
1 M.2 Slot (M-key, SATA & PCIE 3.0 x4, 2242/2260/2280)
1 M.2 Slot (E-key, 2230, for WiFi)
2 SATA3 6Gb/s Connectors
2 USB 3.1 Gen 2 (10 Gb/s) Vertical Type-A Ports
2 USB Pin Header for up to 4 additional USB 2.0 Ports
1 40-pin eDP 1.3 Header (4096 x 2304 @ 60Hz)
1 Chassis Intrusion Jumper
1 AT/ATX Mode Jumper
1 8-bit GPIO Header
1 4-pin SMBUS Header
1 6-pin PS2 Keyboard Mouse Header
1 9-pin Audio Header
1 9-pin Front Panel Header
2 4-pin Fan Headers
1 2-pin +9 ~ 36V Alternate Power-in
1 SATA Power-out Connector
|
| Power Supply for NF797 |
External Power Supply – the board can be powered with a +9 ~ 36V external power supply though a DC connector on the back panel. The rear +9 ~ 36V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9 ~ 36V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +9 ~ 36V 2-pin power connector, where pin 1 is +9 ~ 36V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +9 ~ 36V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9 ~ 36V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Digital Security & Surveillance
√ Digital Signage
√ Gaming
√ Industrial Automation/Control
√ Medical
√ Retail (POS/Kiosk/ATM)
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
