| Model Name | NF835 |
| Part Number | JNF835-8365U |
| Form Factor | 3.5" SBC (148 x 102mm) |
| Processor | Intel® Core i5-8365U, 1.60GHz – 4.10GHz Burst, 4-Core 8-Thread, 15W TDP, vPro
* Ships with flat silver heatsink for direct attaching to a surface |
| Memory | 2 x 260-pin DDR4-2400 SO-DIMM up to 32GB Total |
| Graphics | Intel HD Graphics 620, 300MHz - 1.05GHz (i5-8365UE) |
| Audio | Realtek ALC662 HD Audio
Realtek ALC888 HD Audio (Manufacturered after June 2021) |
| LAN | 1 x Intel i219LM PHY Gigabit LAN
1 x Intel i211AT PCI-E Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s Connector
1 x M.2 SATA & PCIE 3.0 x4 NVME 2242/2260/2280 |
| Super IO | NUVOTON NCT6116D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
* As of 5/11/2020, onboard TPM is now optional |
| Back Panel Connectors |
1 3.5mm Audio Jack (Line-out)
1 USB 3.1 Gen2 Port Type-C
2 RJ45 LAN (10/100/1000)
4 USB 3.1 Gen2 Ports
1 Display Port (4096 * 2304 @ 60Hz)
1 HDMI 1.4 (4096 * 2160 @ 30/24Hz)
1 +9V – 24V 2.5mm Diameter DC Power Jack
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 SATA & PCIE 3.0 x4 NVME 2242/2260/2280
1 M.2 PCI-E 2230 E Key for WiFi
6 Serial Headers (5 * RS232, 1 * RS232/422/485)
2 USB Pin Headers for up to 3 additional USB 2.0 Ports
1 USB 3.1 Gen2 type-A Vertical Port
1 40-pin eDP (4096 * 2304 @ 60Hz)
1 30-pin 24-bit Dual Channel LVDS / 8-pin Inverter (1920 * 1080 @ 60Hz)
1 Chassis Intrusion Header
1 8 bit GPIO Header
1 4-pin 3W Amplifier Header
1 9-pin Front Audio Header
1 4-pin I2C Header
1 4-pin Fan Header
1 6-pin PS2 Keyboard Mouse Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 2-pin +9V – 24V Alternate Power-In (Mating plug: JST VHR-2N or TE 1-1123722-2)
|
| Power Supply for NF835 |
External Power Supply – the board can be powered with a +9V – 24V external power supply though a DC connector on the back panel. The rear +9V – 24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9V – 24V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +9V – 24V 2-pin power connector, where pin 1 is +9V – 24V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +9V – 24V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9V – 24V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Digital Signage
√ Retail (POS/Kiosk/ATM)
√ Factory Automation
√ Industrial PCs
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
