| Jetway NF9N Mini-ITX Motherboard |
| Processor | Intel® Celeron N2930 SoC, 1.83GHz – 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP |
| Memory | 2 x 204-pin SODIMM DDR3L-1333 Single Channel up to 8 GB (1.35V required) |
| Graphics | Intel HD Graphics, 313MHz - 854MHz |
| Audio | Realtek ALC662 5.1 Channel HD Audio with 3W Amplifier |
| LAN | 1 x Intel i211AT Gigabit Ethernet |
| Storage | 2 x SATA2 3Gb/s Connectors
1 x Full-size mSATA slot |
| Super IO | FINTEK F81768D |
| Back Panel Connectors |
1 PS2 Keyboard
1 PS2 Mouse
1 VGA
1 RS232 COM Port
3 USB 2.0
1 RJ45 LAN (10/100/1000)
1 +12 DC-in jack
1 HDMI
1 USB 3.0
1 3.5mm Audio Jacks (Line Out)
|
| Onboard I/O Connectors |
1 Jetway Daughter Board Gen2 Connector
1 PCI Express x1 Slot
1 Full size mSATA Slot (shares with 2nd SATA port)
1 Full size mini PCI-E Slot
2 SATA2 3Gb/s Connectors
2 USB 2.0 Pin Headers for up to 4 additional USB 2.0 Ports
1 Serial Port Header (RS232, +5V/+12V)
1 24-bits Dual Channel LVDS/Inverter (CHRONTEL CH7511B)
1 GPIO header
1 Parallel Port header
1 AT/ATX Mode jumper
1 Chassis Intrusion header
1 9-pin Audio header
1 4-pin Speaker Power header
1 4-pin CD-in header
1 4-pin line-in header
1 2-pin LAN LED header
1 2-pin SPDIF header
1 4-pin SMBUS header
1 Front Panel header
3 Fan headers
1 20-pin ATX Power Connector
1 4-pin SATA Power Output (Male)
1 2-pin 12V ATX Power Connector for alternate internal power supply (Molex 5566-2)
|
| Power Supply for NF9N |
External Power Supply – the board can be powered with a 12V external power supply though a DC connector on the back panel. The rear 12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 12V and the shell is GND.
Internal Power Supply – the board can, alternatively, be powered by an internal 20-pin ATX OR ATX12V 1 x 2 power connector.
Based on power consumption test results, the recommended power rating is 60 W (12V/5A).
Caution: There is no isolation circuitry between the external 12V DC jack and the internal 20-pin ATX & 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12V DC jack is covered if the internal 20-pin ATX OR 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Digital Signage
√ Panel PC
√ Industrial Automation/Control
√ All-In-One
√ Retail (POS/Kiosk/ATM)
√ Casino Gaming
√ Thin Client
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
